—— Best Sellers ——
1 2 3
-
Ezonetronics RM - CT0008 7 inch 1 Din Re...$166.67
-
BOER High-end Ping Pong Racket Table Ten...
$14.45
-
SONOFF CD100S Door Window Sensor Wireles...
$3.55
-
BlackBerry KEY2 4G Smartphone Snapdragon...
$831.74
-
OUKITEL U16 Max 4G Phablet...
$160.97
More Categories :
- JOYO JT - 53 LED Digital Chromatic Tuner for Electronic Acoustic Guitar
- QS QS5013 2.5 Channel RC Helicopter with Gyroscope Infrared Function
- MPOW DS - D6 Waterproof Fitness Tracker Smart Bracelet Heart Rate Sleep Monitor for iOS Android System BLACK
- Rikomagic RKM MK22 TV Box Amlogic S912 Octa Core Android 6.0 2.4G + 5G Dual Band WiFi Bluetooth 4.0 3G DDR3 RAM 32G eMMC ROM
- AEC
- ALLDOCUBE
- EZCast
- Jumper
- Junsun
- Maxsun
- Mirascreen
- XDUOO
- OUKITEL
- View More Brands
3D Printer Touch LCD Screen MKS_GEN Controller Full Color 3.2 Inch MSK TFT32 Touch Screen LCD Display
Details
1.Bed Leveling
Auto Leveling
After the machine assembles with a bed leveling controller, then run leveling on TFT interface.
#The command of auto leveling (G29 is available for Marlin.
While G32 is for Repetier and Smoothieware)
>cfg_auto_leveling_cmd:G28;G29;
Manual Leveling
Manual leveling is good for MB,i3 etc machines. It is available to set 3,4,5 point .
#The point number of manual leveling:(3,4,5 point available)
>cfg_point_number:4
2.Filament Replace
It is easy to replace the filament when it runs out.
You are able to set temperature and the speed of filament in-out on config.
As following:
#the speed of filament replacing(mm/min)
>cfg_filament_change_speed:1200
#the length of filament replacing(mm)
>cfg_filament_change_step:5
#the min temperature of filament replacing
>cfg_filament_limit_temperature:175
3.Print from Breakpoint
TFT has a one of the excellent features is able to print from Breakpoint.
Below is the way to do it.
Firstly, set target temperature of extruder and heated bed, and then preheat.
Secondly, when preheat ready, go home .(Notice: if power off happens during operating printing from breakpoint, please must home .)
Thirdly, move extruder to the breakpoint which is available to set allowable error.
#Breakpoints continued playing Z-axis error setting
>cfg_breakpoint_z_error:0.2
Fourth, click set, and then click Continue(Means Print from Breakpoint).
After that, choose the file you want.
(If you pause the printing, and turn the printer off,
then it will resume to print from the pause point after power on.)
4.Filament Outage Detecting
Connect detecting switch to PB1 of TFT.
Set configuration to trigger low level or high level available.
#the level signal of outage detection module PB1(low level:0; high level:1)
>cfg_PB0_PB1_Level:1
5. Auto off after Print Finishes
Enable this function on config,and take concerted with PWC switch.
#whether set machine auto-off after print finishes(auto-off:1; NO:0)
>cfg_print_finish_close_Machine:0
Auto Leveling
After the machine assembles with a bed leveling controller, then run leveling on TFT interface.
#The command of auto leveling (G29 is available for Marlin.
While G32 is for Repetier and Smoothieware)
>cfg_auto_leveling_cmd:G28;G29;
Manual Leveling
Manual leveling is good for MB,i3 etc machines. It is available to set 3,4,5 point .
#The point number of manual leveling:(3,4,5 point available)
>cfg_point_number:4
2.Filament Replace
It is easy to replace the filament when it runs out.
You are able to set temperature and the speed of filament in-out on config.
As following:
#the speed of filament replacing(mm/min)
>cfg_filament_change_speed:1200
#the length of filament replacing(mm)
>cfg_filament_change_step:5
#the min temperature of filament replacing
>cfg_filament_limit_temperature:175
3.Print from Breakpoint
TFT has a one of the excellent features is able to print from Breakpoint.
Below is the way to do it.
Firstly, set target temperature of extruder and heated bed, and then preheat.
Secondly, when preheat ready, go home .(Notice: if power off happens during operating printing from breakpoint, please must home .)
Thirdly, move extruder to the breakpoint which is available to set allowable error.
#Breakpoints continued playing Z-axis error setting
>cfg_breakpoint_z_error:0.2
Fourth, click set, and then click Continue(Means Print from Breakpoint).
After that, choose the file you want.
(If you pause the printing, and turn the printer off,
then it will resume to print from the pause point after power on.)
4.Filament Outage Detecting
Connect detecting switch to PB1 of TFT.
Set configuration to trigger low level or high level available.
#the level signal of outage detection module PB1(low level:0; high level:1)
>cfg_PB0_PB1_Level:1
5. Auto off after Print Finishes
Enable this function on config,and take concerted with PWC switch.
#whether set machine auto-off after print finishes(auto-off:1; NO:0)
>cfg_print_finish_close_Machine:0
Materials: Plastics
Suitable for: Mainboard Control
Type: DIY Accessories
Suitable for: Mainboard Control
Type: DIY Accessories
Package size: 15.00 x 11.00 x 5.00 cm / 5.91 x 4.33 x 1.97 inches
Package weight: 0.132 kg
Package weight: 0.132 kg
Package Contents: 1 x3d touch screen printer
